QuadFusion Documentation
M3D HomeGithub Repository
  • Welcome
  • Facebook Group
  • Getting Started
    • Critical Warnings & Information
    • Unboxing & Inventory
    • Getting Connected
    • Updating Firmware
    • Updating your Control Board Settings
    • Changing Homing Offsets
    • First Print
    • Getting Started: Where to Go From Here
  • Printer Installation
    • M3D Crane
    • M3D ProMega
    • CR-10S
    • Prusa i3 MK2S
    • Duet Maestro Wiring
  • Beginner Guides
    • Beginner: Preparation
    • Beginner: QuadFusion Assembly
    • Beginner: Moving the Motors
    • Beginner: Introduction to G-Code Commands
    • Beginner: Software Layers
    • Beginner: What is Slicing?
    • Beginner: Printing the Print
    • Beginner: Where to Go From Here
  • Electrical Guides
    • The Electrical Standard
  • Firmware Guides
    • Adjusting Homing Macros
    • Macros
  • Printing Guides
    • Slicers and Printer Settings
    • Heating & Temp Sensor
    • Loading and Unloading Filament
    • (NEW) Loading and Unloading Filament
    • Filament Success Guide
      • ABS-R
      • PLA
    • Filament Extrusion Rate
    • Tool Definitions
  • Color Printing
    • Setting Up
    • MELT
    • Slic3r Multi-Material
  • Troubleshooting Guides
    • Troubleshooting Duet Web Console
    • My Drives / Tools are Backwards
    • Heater Troubleshooting
  • Maintenance Guides
    • What You'll Need
    • Temperature Calibration
    • Changing Nozzles
  • Community Guides
    • Community Guide Template
Powered by GitBook
On this page
  • Brief Overview
  • All Tools
  • All Screws
  • Detailed List
  • QuadFusion Assembly
  • Hot-end Assembly
  • Fan Mount Assembly
  1. Maintenance Guides

What You'll Need

This guide contains a list of different screws and tools used for each assembly of the QuadFusion and its fans. Look under the tool's header for each assembly to see all the possible tools you will need to maintain, assemble or repair the QuadFusion or its fans . Look under the screws category to view a more in-depth list of the screw types and their location.

Brief Overview

All Tools

  • T-10 Torx Screwdriver

  • T-6 Torx Screwdriver

  • 2.5 mm Hex

  • 1.3 mm Hex

  • Pliers

  • Needle-nose pliers

All Screws

  • Hot-end Block Set screws: 1.3 mm Hex

  • Fan mount: T-10 Torx

  • Fan Duct: T-6 Torx

  • QuadFusion: T-10 Torx and 2.5 mm Hex*

    • *The 2.5mm Hex screw may vary based on how you are mounting your QuadFusion. Go to the Mounting the Hardware guide for more information.

Detailed List

QuadFusion Assembly

Tools

  • T-10 Torx

  • 2.5 mm Hex

Screws

2.5 mm Hex:

  • Mounting Quad (bottom)

T-10 Torx:

  • Mounting Quad (top)

  • Nozzle Screw

Hot-end Assembly

Tools

  • 1.3 mm Hex

  • Pliers

Screws

1.3 mm Hex:

  • PT1000 Setscrew

  • Heater Cartridge Setscrew

  • Nozzle Setscrew

Fan Mount Assembly

Tools

  • T-10 Torx

  • T-6 Torx

Screws

T-10 Torx:

  • Fan Mounts

T-6 Torx:

  • Fan Ducts

PreviousMaintenance GuidesNextTemperature Calibration

Last updated 6 years ago